Installation Of A Metal Bath

Despite the arrival on the market of bathtubs made of modern materials: quartz, acrylic, cast marble, steel bathtubs are still popular among consumers.

First of all, due to its durability. But in order for the font to serve you faithfully for many years, it must be installed correctly.

Therefore, we have created the most detailed instructions for installing a steel bath . Where all expert advice is collected. It will save you from installation errors. And it will also show how the shortcomings of metal models can be turned into advantages.

Preparatory works

Have you already chosen a bath? If so, you can start preparing the room for its installation.

There are three types of font installation:

  • in the tiled bathroom;
  • to bare walls with subsequent tiling;
  • to the walls lined to the planned level of installation of the bathtub.

Let’s figure out – which one is better to use and when.

The first method is convenient if you bought a high-quality massive steel bathtub that does not require additional fastening to the walls. Here everything is simple and fast – the basin is placed on legs and pushed to the wall. It is only important not to forget about sealing the joint.

The second method will allow you to make high-quality stops on the walls, without violating the integrity of the tiles. Plus, it will be much easier to seal the joint, since the tiles will be laid from the side. Therefore, water will definitely not get under it. The disadvantages of this option include the fact that laying tiles will not be very convenient and quite dangerous for covering the bathtub. If you decide to make wall cladding already after installing the font, in no case do not remove the factory film from the bowl. And even better, cover the bottom and sides of the bathtub with cardboard. This will keep the enamel coating intact.

And finally, the third method is the most, in our opinion, optimal, but also the most difficult. After all, it is very important to measure everything accurately, so that the font would clearly fall into the height of the space that is not lined with tiles. With this option, you will not damage either the tile or the coating of the bowl.

The options have been decided. Now you need to clean the room well and prepare the tool. About it below.

Tools

First you need to prepare the tools. For comfortable work, you will need:

  • level — for setting the horizon line;
  • roulette;
  • building marker for marking;
  • a set of wrenches — for adjusting the legs;
  • corner — for inspection of right angles;
  • perforator for drilling holes in the wall;
  • screwdriver or screwdriver.

Step-by-step instructions for installing a metal font

Thermal and sound insulation

Despite all the undeniable advantages of steel models, they have their drawbacks: high thermal conductivity (water cools down very quickly) and poor noise insulation (the sound of filling the bathtub can be heard even by neighbors). But both of these problems are quite easy to deal with. There are many different materials that can be used to cover the walls and bottom of a steel bowl to improve its characteristics.

How to assemble and install the legs with your own hands?

After performing the insulation work, you can start installing the legs. They are:

  • universal – as a rule, such legs come with the cheapest models and are simply attached to an adhesive base;
  • with a bolted connection – such models are more thorough, they are connected to the bottom with the help of special bolts. There are different options for their implementation, but the principle of installation is the same for all of them.

STEP 1 . A bolt is inserted into a special fastening place at the bottom of the bowl.

STEP 2. Then the support frame is put on it. The structure is fastened with a nut. To reduce the load on the bowl, it is important not to forget to lay rubber spacers between the bottom and the legs.

STEP 3 . After that, you need to screw the legs to the frame. You shouldn’t tighten them too much. Since the bath will still need to be leveled.

STEP 4 . It remains only to put on plastic pads to reduce the pressure of the legs on the floor.

Drain-overflow

It is better to collect the drain-overflow at the stage when the bathtub is still lying on the floor – it will be more convenient that way. You can do this according to the standard instructions:

  1. gaskets are inserted into elements (10), (7 — siphon), (4), and then they are connected to each other with plastic nuts (8);
  2. gaskets (18), (15) are inserted into the corresponding overflow elements (17), (14), which are fastened with nuts;
  3. the collected drain and overflow are applied to the holes in the bath, and bolted to the bars.
Level adjustment

After installing all the elements, you can turn the basin over on its legs and put it in the place of the future dislocation. Next, it is necessary to set it flat with the help of a building level. Put the level one by one on each side of the bath, twisting the corresponding legs. After all the boards are exposed, you can proceed to the next stage.

If the length of the legs is not enough to reach the required height and the question has arisen about how to lengthen them, everything is simple here. You can put bricks under them, having previously fixed them to the floor with mortar.

Many craftsmen try to make an additional slope by adjusting the legs. Allegedly, the water would flow better. This is a mistake! In all models, this slope is provided technologically, the bathtub must be placed strictly on the level!

Additional supports than to be fixed to the wall so that it does not wobble?

As already mentioned above, a high-quality steel bath with walls 3 mm thick does not need additional supports, and it is not necessary to attach it to the wall at all. But if the purchase is not the most expensive or you want to insure against the fact that it will wobble, you can make a frame for the bathtub. Or screw additional supports for the sides to the wall. Let’s figure out how to do it better.

STEP 1 . First, you need to measure the distance from the floor to the lower edge of the bathtub (distance “A”). Then you need to move the bathtub and set aside this distance from the floor with the help of a tape measure, drawing a board line around the entire perimeter.

STEP 2 . As an additional support, you can use a high-quality galvanized profile, steel corners or a wooden beam treated with a special moisture-resistant impregnation. With the help of dowel nails, it is necessary to fasten them to the wall along the line that we drew at the last stage. They will take part of the load off the legs. The sides of the bath will rest on them.

Next, you should coat the supports well with sealant and install the font on them, this will strengthen the structure so that the bowl does not wobble or creak.

Grounding of an iron cup

The next important step is grounding the bowl. Metal baths must be grounded, as steel is an excellent conductor. And in the case of a phase falling, for example, on a metal pipe, the result can be deplorable.

Baths usually have a special grounding bolt with a special marking. It must be connected to the nearest point of the ground circuit using a copper wire. As a rule, in San. socket nodes always have a grounding conductor, so you can connect a grounding wire to it.

Sealing

The final stage is the sealing of the joint between the wall and the tile.

You can close the seam between the iron bath and the tile with the help of silicone sealant. It must be applied along the entire perimeter of the board’s contact with the wall.

Then wet it with a spray bottle and remove the excess with your finger or a special spatula.

If they are additionally moistened, the work will be done even more accurately.

Screen

In order for the hon. the node looked more aesthetically pleasing, the space under the bathtub is better to cover with a screen. You can make a blind screen from tiles. But in order to effectively use the space under the bathtub, a screen with sliding doors is best suited.

Conclusions

As you understood from the article, it is quite possible shower replacement sacramento with your own hands. You only need tools and a little perseverance.

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button